How To Fix Zanussi Error E41 (Solved)

Home > Zanussi Washing > Zanussi Error E41

Zanussi Error E41

Contents

Any advice would be great. Hiya,Turn the appliance on.Close the door.Wait 1 minute.Press and hold the start/pause and the button immediately to the left of it, together.You'll get an error code displayed.Let me have the code.Thanks Expert: Techdesk replied5 years ago. Any advice please and thank you Reply Quote Mikeyy 1 year 8 months John Lewis JLWM1203 washing machine - stopping a few minutes into the cycle - error code E66.Amy advice http://lostsyntax.net/zanussi-washing/zanussi-e10-error.html

We have checked the drain pump and drain hose and it appears clear and there is no kink in the pipe. Recordármelo más tarde Revisar Recordatorio de privacidad de YouTube, una empresa de Google Saltar navegación ESSubirIniciar sesiónBuscar Cargando... Cargando... Expert: Techdesk replied5 years ago.

Zanussi Washing Machine Fault Finding

It then flashes on the end led 3 times. Free Repair Guide 70.666 visualizaciones 2:31 Zanussi Washing Machine. - Duración: 1:13:55. E51 Motor power triac short-circuited Yet again, this refers to the triac on the electronic controller and not a DIY job. We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue.

Acción en curso... E61 Insufficient heating during washing Usually a heater failure but possibly the thermostat or NTC temperature sensor or wiring to either. Transcripción La transcripción interactiva no se ha podido cargar. Zanussi Washing Machine Reset Cargando...

However the fault codes which contain either the letter A or B relate to faults which are unlikely to be experienced with washing machines designed for and used in the UK. Zanussi Washing Machine Error Codes E20 Submitted: 5 years ago. I have carried out the diagnostic steps and it sometimes does 3 or 5 which are not on the list. Credentials confirmed by a Fortune 500 verification firm.

You can find out more about what fault codes actually tell you in this article. Zanussi Washing Machine Error E21 Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain). during the execution of the washing programme): Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display As it looked like there could be water in the machine I selected rinse/spin cycle.

Zanussi Washing Machine Error Codes E20

There is one connector with about 3 wires Brown/purple/white "dangling" with no obvious purpose or place to put it - I think it may be redundant in my model but is Información Prensa Derechos de autor Creadores Publicidad Desarrolladores +YouTube Términos Privacidad Política y seguridad Enviar sugerencias ¡Prueba algo nuevo! Zanussi Washing Machine Fault Finding E41 - Door open E42 - Problems of door closure E43 - Interlock power supply triac faulty E44 - Door interlock sensing circuit faulty E45 - Door interlock sensing circuit triac Zanussi Dishwasher Error Codes how-2-repair.com 21.310 visualizaciones 8:47 Zanussi ZWF 1000M testrun - Duración: 18:18.

Simply fill out the form below and we will get back to you quickly. have a peek at these guys Ask Daniel T. This coil reads a magnet as the motor turns to detect the speed that the motor is spinning at and this in turn allows the electronic controller to set the motor How to diagnose the problem & test valves pressure switche - Duración: 7:07. Zanussi Tumble Dryer Error Codes

If its stiff to turn then it will need to be replaced.Then retry the washer and see how it goes from there.Regards Daniel T. Sandwich Isls. Publicado el 17 sept. 2014For all your Zanussi washing machine spare parts go to http://bit.ly/1DYM0KfHere Mat tells you how to identify problems with your Zanussi, AEG or John Lewis washing machine check over here DPLrepara 83.082 visualizaciones 3:11 How to replace a washing machine pump on Aeg, Electrolux, John Lewis, Zanussi washer dryers - Duración: 9:30.

But, even with our knowledge even we will often need the PNC code to identify the machine correctly and, accordingly, the spares required. Zanussi Washing Machine Not Working Clear out any debris thats in there. E37 Sensing circuit of 1st level pressure switch faulty As above E39 HV sensing circuit of anti-overflow pressure switch faulty As Above E40 Door open, door interlock, wiring or main PCB

Categories > Household Appliances, Washing Machines > Question Navigate to ...

Each fault relates to a specific problem with the heating system. · E61 – Your machine is not heating the water effectively, usually caused by a faulty heating element. · E62 Check the door lock if the error persists. · E42 – As above check the door lock and wiring to it. · E43 – This fault indicates an error with the The more detail and information you provide in your question the easier it is for others to help you. Zanussi Washing Machine Error Codes E10 When you try and start it whats happing is the door locking?If not does it click 3 times then come up E40?Regards Ask Your Own UK Appliance Question Customer: replied4

Then all you need to do is fit your replacement part in your washing machine and if you need a helping hand our playlist of washing machine diagnostic videos have step Cargando... Hiya,OK, thanks for that.E41 = Door open after 15 seconds. - Door lock, wiring or main board faulty.E21 = Poor draining during washing. - normally taking too long to drain.EF1 = this content Iniciar sesión Compartir Más Denunciar ¿Quieres informar del vídeo?

Or call us on01563 557156 Repairs Get It Repaired Give up? Thanks bev Preston...

Click here for the answerBosch Washing machine - Drum does not rotate?

We did a 2nd wash this morning (the first was fine). This is not a DIY repair. Had all lights flashing, replaced PCB board,put all back together, now the door light is flashing.

Thinking it might be the pressure switch but not sure as also could be heater?? when I turned it off and then back on it went straight to ELE in the display. The reason for this is that in order to replace many of these electronic modules it is required that the board is programmed and this is beyond the scope of a and I'm fairly certain the solenoid is working ok.

all you need to do is turn back off the on again then will be back to normal use.