Fix York Furnace Gas Valve Communication Error (Solved)

Home > Error Codes > York Furnace Gas Valve Communication Error

York Furnace Gas Valve Communication Error

Contents

To stop this mode, cycle power to the furnace off and then back on. We checked the wires hardness from the board to the gas valve wouldn't find any broken wires and all other sensor devices seemed working normally during the sequence of operation. Interrupt power to your furnace for 20 seconds or lower the thermostat so your furnace does not try to heat, then reset the thermostat to the previous setting. Most newer furnaces will have a diagnostic center or control built into the control module. navigate here

I believed the problem was the pressure switch. CRTC Net Neutrality Debates [CanadianBroadband] by thehammer86557. Apparently mositure from the intake pipe is damaging the gas valve. The control will flash “3” on the LED until the limit switch closes.

Carrier Furnace Error Codes

This condition may be caused by: dirty filter,improperly sized duct system, incorrect blower speed setting, incorrectfiring rate or faulty blower motor. Industrial 23932409 Type Your HVAC Question Here... The control module will indicate a call for heat with a light on the control either blinking or remain solid depending upon model. I checked the same things I did last time, but had to hurry off to work.After doing some googling, it seems to me that this could be a problem with the

I repeated the procedure, and it worked again.Went out, picked up a new pressure switch and the heat has been going fine ever since.Hope this helps. · actions · 2010-Jan-8 10:05 Reason: typo 12-29-2009,10:50 PM #25 beenthere View Profile View Forum Posts View Forum Threads Global Moderator Join Date Jan 2004 Location PA Posts 72,934 Post Likes Likes (Given) 246 Likes (Received) Something initially clicks, not sure what.2. Blinking Red Light On Furnace It had registered for 10 years parts warranty.

SuperCool Slide Rule 172,881 views 5:44 HVAC AC Blower not working, troubleshooting Fan Control board, Fan not working. - Duration: 8:13. Lennox Furnace Error Codes Please enter a valid email address. Lastly a safety sensor will be looking for a certain temperature within a few seconds and the furnace will continue to operate and the room air blower will turn on in Either a pilot will come on or the burner tube will ignite then spread the flame to all burners.

Your furnace may have a pinched or blocked pressure switch hose, a blocked flue or loose wiring.10. Carrier Error Codes The firing rate is automatically adjusted to meet demand, increasing gradually to maximum 100% firing rate if the thermostat is not satisfied within a defined time.I've heard that they've been having Dec 04, 2008 | Goodman GMS90703BXA Heater Not finding what you are looking for? And if any technicians have better ideas to solve the problem, please give us an advice, we would be very appreciate.

Lennox Furnace Error Codes

Flash sequence codes 1 through 10 are as follows: LED will turn “on” for 1/4 second and “off” for 1/4 second. Did you ohm the harness with a meter or just do a visual inspection? Carrier Furnace Error Codes Five Amber Flashes - Heating capacity is reduced due to restriction in the combustion air or vent system. Rheem Furnace Error Codes Same thing, glows like a bulb, the style my system uses, the "filament" for lack of a better word is a wide helix of black dark grey material supported by a

If a system problem occurs, a blinking LED shows a fault code. If the flame current is below 1.0 uA (+/-50%), the flame LED will flash slowly to indicate “weak” flame. If it does, tape down the door safety switch and cycle the furnace with the panel off. Cleaned out the condensate line. Flashing Green Light On Furnace

The furnace doesn't seem to shut down once it's lit either (it did once, but in the 100+ cycles I've watched I don't think that's indicative of another problem).Since I already Nov 20, 2009 York ignition lockout due to retries Dec 29, 2008 More results from www.doityourself.com 7 Tips and Tricks to repair your Furnace DIY - YouTube ? 13:25 https://www.youtube.com/watch?v=rAtcvPqUsBA Dec Read continuous flashing on the LED to mean your furnace has a reversed polarity of 115 volts. his comment is here Just an FYI - just because a switch ohms out OK doesn't mean its going to carry current.

The furnace will lock out for one hour and then restart. 8 RED FLASHES: This fault is indicated if the flame is lost 5 times (4 recycles) during the heating cycle. Lennox Furnace Diagnostic Codes Still trying to determine for sure what the 5 flashes mean exactly. Bothheating and cooling operations will be affected.

check air filter, clean blower wheel, and check to make sure the blower wheel is running at proper speed and not dragging sometimes cause by a weak capacitor.

Make sure to check for gas leaks when you have it all back together.Do you have propane or natural gas? · actions · 2010-Jan-7 7:12 pm · Thane_BitterInquire withinPremium Memberjoin:2005-01-20·Start.ca·Bell Fibe Both heating and cooling operations will be affected. Rheem failure codes FLAME LEDThe FLAME LED is an indication of thepresence of flame.OFF – No flame is detected.Rapid Blink – Unexpected FlameSlow Blink – Marginal Flame SenseSteady ON – Normal Bryant Furnace Error Codes Switch will not open.5 Blinks – Not applicable.6 Blinks – Line and Neutral reversed.POWER LEDThe POWER LED is an indication of24ac power to the board.OFF – No power (24VAC) to controlboard.ON

To print the manual completely, please, download it. When all else fails, you have to call an expert, but first try the steps in this video.Here is a list of codes that was posted to www.doityourself.com by Huston204Flash sequence After one hour of lockout, your furnace will automatically reset itself and try to operate as usual.3. Either the gas valve opens up and the furnace completes it's normal cycle, or the gas valve doesn't open up and it seems to cycle the glow plug off and on

The control continually tries to establish communication and automatically resumes normal operation when communication is re-established. What could go wrong?